Model: IM200 F18
Part No. 901000
18 Gauge Finish Nailer
P
CORDLESS
18 GA
UGE CORDLESS
FINISH NAILER
OPERATING MANUAL
IMPORTANT!
DO NOT DESTROY
It is the customer's responsibility to have
all operators and service personnel read
and understand this manual.
Printed in U.S.A.
© 2001 Illinois Tool Works, Inc.
901070-2
10/01
Introduction and Warranty
The Finish nailer should be handled like other power
fastening tools that you use. Like most tools, when used
improperly injury could result . If you are going to allow
others to use the Finish nailer, it is your responsibility to
make sure that they also read and comply with the
instructions in this manual before attempting to operate
the tool.
TrimMaster 18™ Finish Nailer
Operating Manual
This manual is intended to acquaint you with the Paslode
Cordless 18 Finish Nailer. Unlike other power fastening
tools, the Cordless 18 Finish Nailer is powered by an
internal combustion linear motor. In simpler terms, your
Cordless 18 Finish Nailer is powered by a motor similar to
the one that powers an automobile. The Cordless 18 Finish
Nailer ignites a fuel and air mixture to produce the energy to
drive the motor, which in turn drives the fastener. The
Cordless 18 Finish Nailer is totally self-contained. It carries
its own fuel supply and battery, along with a supply of
fasteners.
ShouldyouhavequestionsabouttheFinishnailer,orwish
to obtain additional copies of this manual, please contact
yourPaslode®representative.Thespacebelowisprovided
so that you may record your representative's name,
address, and telephone number.
For the nearest Paslode representative call 1-800-
682-3428
For ease of use, this manual is divided into sections (see
Contents). Each section of the manual is written with you,
the tool operator, in mind. We have left out many of the
technicaltermssothatyoucaneasilyunderstandhowtoget
the maximum performance from your Cordless 18 Finish
Nailer, and how to avoid damaging the tool or injuring
yourself. But, to accomplish this, we need you to do two
things:
Name
Address
1. READ THE MANUAL FROM COVER TO COVER
BEFORE USING THE TOOL.
City
State
Zip
2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.
Telephone Number
Cordless Warranty and Limitations
Paslode warranties that new Cordless power fastening tools,
WARRANTY STATEMENT
parts and accessories will be free from defects in material and
workmanship for the period shown below, after the date of
delivery to the original user.
Paslode's sole liability hereunder will be to replace any part or accessory
whichprovestobedefectivewithinthespecifictimeperiod.Anyreplacement
part or accessory provided in accordance with this warranty will carry a
warranty for the balance of the period of warranty applicable to the part it
replaces. This warranty does not apply to part replacement required due
to normal wear.
ONE-YEAR LIMITED WARRANTY
A one-year warranty will apply to all parts, except those listed
below as normal wearing parts, or parts which are specifically
covered by an extended warranty.
This warranty is void on any tool which has been subjected to misuse,
abuse,accidentalorintentionaldamage,usewithfasteners,fuel,batteries,
or battery chargers not meeting Paslode specification, size, or quantity,
improperly maintained, repaired with other than genuine Paslode
replacement parts, damaged in transit or handling, or which, in Paslode's
opinion, has been altered or repaired in a way that affects or detracts from
the performance of the tool.
FIVE-YEAR EXTENDED LIMITED WARRANTY
A five-year warranty will apply to all molded nylon parts:
•
•
•
Cap and Grille
Handle Halves and Actuator
Trigger
PASLODE MAKES NO WARRANTY, EXPRESSED OR IMPLIED,
RELATING TO MERCHANTABILITY, FITNESS, OR OTHERWISE,
EXCEPTASSTATEDABOVE,andPaslode'sliabilityASSTATEDABOVE
AND AS ASSUMED ABOVE is in lieu of all other warranties arising out of,
or in connection with, the use and performance of the tool, except to the
extent other wise provided by applicable law. PASLODE SHALL IN NO
EVENTBELIABLEFORANYDIRECT,INDIRECT,ORCONSEQUENTIAL
DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES WHICH
MAY ARISE FROM LOSS OF ANTICIPATED PROFITS OR
PRODUCTION, SPOILAGE OF MATERIALS,, INCREASED COST OF
OPERATION, OR OTHERWISE.
90-DAY LIMITED WARRANTY
A 90-day warranty applies to the following parts, which are
considered normal wear parts:
•
•
•
Bumper
Driver Blades
O-Rings
2
An Overview of the Cordless TrimMaster 18™ Finish Nailer
Description
Specifications
Dimensions: Weight-with battery
4 lbs 14oz.
11-1/2 inches
11 inches
The TrimMaster 18™ Finishnailer is a self-contained, fully
portable nailer that uses liquid hydrocarbon fuel to power a
unique linear drive internal combustion motor.
Height
Length
Magazine
Straight 18 Ga.
Inorderforyoutofullyunderstandtheinformationcontained
in this manual, you need a basic understanding of the
TrimMaster 18™ Finish nailer. As you can see in the
illustration below, the Impulse Finish nailer is made up of
three major areas: handle, motor, and magazine.
Cycle Rate:
Intermittent Operation – 2 to 3 nails
per second
Continuous Operation – 500 nails
per hour
As you examine the TrimMaster 18™ Finish nailer, become
familiar with the three major areas and the various
components located in each of them.
NOTE: Exceeding these cycle rates could cause the tool to
overheat, resulting in loss of performance or damage to tool
components.
The Handle contains the fuel cell, indicator light, and the
trigger.
ByusingtheTrimMaster18™Finish nailerat itsrecommended
cycle rate, you will be able to drive several thousand nails in
a typical workday.
The Motor contains the cover and filter, the motor housing,
the nose, and the work contacting element.
Fasteners:
18gauge, straight F-18Series, ChiselPoint
TheMagazinecontainsthecomponentstoload andcontrol
thefastenerandthebatteryfortheCordless18Finishnailer.
Magazine Capacity: 2 nail strips, or 100 fasteners
Battery :
6 volts DC - Provides enough energy to
drive approximately 4000 fasteners on a full
charge.
removable
cover & filter
Fuel Cell:
Liquid hydrocarbon - Provides enough fuel
to drive approximately 1200 fasteners.
(Shelf life 12 months)
fuel cell compartment
Handle (soft grip)
cap
reversable
belt hook
motor housing
magazine release latch
soft
touch
trigger
Motor
Magazine
quick clear
cover
battery indicator light
(opposite side)
adjustable
depth of drive
(opposite side)
nail count indicator
battery compartment
(opposite side)
follower
no-mar tip
3
Safety Instructions
The following safety instructions have been included in this
booklet to provide you with basic information necessary for
safeoperationoftheTrimMaster18™ FinishNailer.DONOT
ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE
READANDUNDERSTANDALLSAFETYPRECAUTIONS
AND MANUAL INSTRUCTIONS.
WARNING
Do not expose the tool to
temperatures in excess of
120° F (49° C). Fuel and/
or the battery may burst,
releasing flammable gas.
DANGER
The TrimMaster 18™
Finish Nailer is an internal
combustion device. It
produces hot exhaust
gases that may ignite
flammable materials. This
tool must not be used in a
combustible environment
or in the presence of
combustible materials,
such as flammable
WARNING
This tool must be operated
only in a well-ventilated
environment, because the
tool exhausts carbon
monoxide similar to a gas
chainsaw or lawnmower.
Exposure to carbon
chemicals, adhesives,
gasoline, or solvents.
monoxide may cause
dizziness, nausea, or
unconsciousness.
WARNING
Do not attempt to
operate this tool until
you have read and
understood all safety
precautions and manual
instructions. Failure to
follow all safety
WARNING
ALWAYS keep the
TrimMaster 18™ Finish
Nailer, fuel cell, battery
and battery charger out
of the reach of children.
precautions and
instructions may result in
a permanent loss of
vision, serious personal
or even fatal injury,
property damage and/or
tool damage.
4
Safety Instructions
7. NEVER OPERATE THE TOOL WITH THE WORK
CONTACTINGELEMENTREMOVEDORDISABLED.
WARNING
This device helps reduce the possibility of accidental
fastenerdischargebypreventingthetoolfromoperating
until it is completely against the work surface.
Always wear EYE and
EAR safety gear when
working with or in the
vicinity of the TrimMaster
18™ Finish Nailer.
NEVER operate the tool if the work contacting element
is not working properly.
8. ALWAYS POINT THE TOOL AWAY FROM
YOURSELF AND OTHERS WHEN CLEARING
JAMS OR REMOVING FASTENERS.
1. Eye protection must meet the requirements of ANSI
Standard Z87.1 and should have side shields for
increased protection.
Pull the follower slightly back and push the release
lever. Tip the tool nose up slightly and fasteners should
slide out of the rear of the magazine. If fasteners are
jammed, refer to the appropriate servicing section of
this manual.
2. NEVER ASSUME THE TOOL IS EMPTY.
Never point the tool at yourself or anyone else.
3. NEVERENGAGEIN"HORSEPLAY"WITHTHETOOL.
9. NEVER OPERATE THE TRIMMASTER 18™ FINISH
NAILER IF PARTS ARE LOOSE, DAMAGED OR
MISSING.
TheTrimMaster18™ FinishNailerisnotatoy–itisatool.
Careless and improper use may result in a serious
accident.
10. DO NOT DRIVE FASTENERS INTO KNOTS OR ON
TOP OF OTHER FASTENERS.
4. NEVERCARRYTHETOOLWITHYOURFINGERON,
OR SQUEEZING, THE TRIGGER.
A fastener may ricochet and cause serious injury.
11. OPERATE THE TOOL ONLY ON THE WORKPIECE.
This practice may result in the accidental discharge of
a fastener.
WARNING
5. NEVER OPERATE A MALFUNCTIONING TOOL.
Refer to the servicing or troubleshooting section of this
manual to correct the problem. If the problem cannot be
corrected, stop using the tool and report it to your
supervisor or Paslode® representative.
TheTrimMaster18™ Finish
Nailershouldbeoperated
only when it is in contact
with the work surface.
When fastening thin
materials such as
plywood, be sure to
position the tool so that
the fastener is driven into
the underlying piece.
6. DO NOT LOAD FASTENERS WITH THE TRIGGER
AND/ORWORKCONTACTINGELEMENTPRESSED
IN.
A fastener may be accidentally discharged.
5
Safety Instructions
12. NEVER DRIVE FASTENERS INTO AREAS WITH 15. PROPERLY STORE FUEL CELL.
CONCEALED HAZARDS.
Always check the area behind the work surface for
electricalwiring,gaspipes,waterpipes,sewerdrainsor
WARNING
other potential hazards.
Always store fuel cells
where they will not be
exposed to an open
13. ALWAYSMAINTAINSECUREANDUNOBSTRUCTED
FOOTING WHEN ON LADDERS, PLATFORMS OR
OTHER HIGH LOCATIONS.
flame,
sparks
or
temperaturesabove120°
F (49° C).
WARNING
Never over-reach, since
tool recoil may cause a
loss of balance. Always
be aware of edges and
drop-offs when nailing on
rooftops and other high
locations. Keep them in
full view.
16. ALWAYS STORE THE TOOL WITH THE FUEL CELL
AND BATTERY REMOVED.
Store the fuel cell in the case with the TrimMaster 18™
Finish Nailer.
17. KEEP THE TOOL CLEAN.
A clean tool is less likely to jam or malfunction.
18. KEEP YOUR HANDS CLEAR OF THE WORK AREA
SURFACE.
14.ALLOWONLYQUALIFIEDPERSONNELTOOPERATE
THE TRIMMASTER 18™ FINISH NAILER.
WARNING
WARNING
A fastener may exit at an
angle unexpectedly and
cause injury.
Onlypersonswhohaveread
and fully understand all tool
operation safety and
maintenance instructions
shouldbeallowedtooperate
the tool.
Battery Disposal:
The Paslode batteries contains cadmium and must be recycled or disposed of properly. It is illegal in some areas
to place a nickel-cadmium battery into the trash or solid waste stream. You may contact your local recycling center
for information on where to return the spent battery or call 1-800-822-8837 for information on Ni-Cd battery recycling
in your area.
6
|